Influence of solvent on solution processed Cu2ZnSnS4 nanocrystals and annealing induced changes in the optical,structural properties of CZTS film

The well-known quaternary Cu₂ZnSnS₄ (CZTS) chalcogenide thin films are playing an important role in modern technology. The CZTS nanocrystal were successfully prepared by solution method using water, ethylene glycol and ethylenediamine as different solvent. The pure phase material was used for thin film coating by thermal evaporation method. The prepared CZTS thin films were characterized by XRD, Raman spectroscopy, FESEM, XPS and FT-IR spectroscopy. The XRD and Raman spectroscopy analysis revealed the formation of polycrystalline CZTS thin film with tetragonal crystal structure after annealing at 450 ^°C. The oxidation state of the annealed film was studied by XPS. A direct band gap about 1.36 eV was estimated for the film from FT-IR studies, which is nearly close to the optimum value of band gap energy of CZTS materials for best solar cell efficiency. The CZTS annealed thin films are more suitable for using as a p-type absorber layer in a low-cost solar cell.     

Synthesis and characterization of molybdenum incorporated mesoporous aluminophosphate

A synthesis of molybdenum incorporated mesoporous aluminophosphate with long-chain n-alkylamine as template material had been prepared under non-aqueous condition. These materials were extensively characterized by using X-ray diffraction (XRD), nitrogen sorption isotherms, nuclear magnetic resonance of ²⁷Al and ³¹P (NMR), inductive coupled plasma (ICP), electron spin resonance (ESR), Fourier transform infrared (FTIR) and thermogravimetric-differential thermal analysis (TG-DTA). Morphology of the materials had been observed by using transmission electron microscope (TEM) that revealed the mesoporous materials possessed wormhole-like structures. Alkaline solvent extraction using n-butylamine/ethanol had been efficiently removed the n-alkylamine from the mesoporous samples which yielded BET surface areas around 550-730 m²/g. BJH analysis showed a narrow pore size distribution which increased with increasing of the carbon chain length of alkylamine (template). Valence state and coordination of the molybdenum in the obtained samples were investigated by using ESR and FTIR where it was found that Mo⁴⁺ and Mo⁶⁺ molybdenum species existed in the molybdenum incorporated mesoporous aluminophosphate in tetrahedral coordination.     

FT-IR study on solvent effects in building blocks of bioactive compounds. V

3-Hydroxy-4-hydroxymethyl pyrrolidin-2-ones, easily prepared from the Baylis–Hillman adduct 1-ethyl-4-methyl-2-hydroxy-3-methylenebutanedioate, are useful intermediates in the synthesis of bioactive compounds. In order to understand the mechanism involved in this reaction, vibrational and Montecarlo molecular mechanics conformational analysis on 1-ethyl-4-methyl-2-hydroxy-3-methylenebutanedioate were carried out, confirming the existence of a low energy intramolecular H-bonded five-member ring.     

Optimization of the synthesis of non-symmetrical alkyl dimethyl sulfonium halides

This work is aimed at the optimization of the yield and purity of non-symmetrical trialkyl sulfonium halide salts. The effects of parameters such as solvent, temperature and concentration were studied. The products were carefully analyzed and the crystal structure of [{n-CH₃(CH₂)₁₅}(CH₃)₂S]Br determined. The overall aim of the present study is future syntheses of low-dimensional magnetic materials.     

Chaotic-to-ordered state transition of cathode-sheath instabilities in DC glow discharge plasmas

Transition from chaotic to ordered state has been observed during the initial stage of a discharge in a cylindrical DC glow discharge plasma. Initially it shows a chaotic behavior but increasing the discharge voltage changes the characteristics of the discharge glow and shows a period subtraction of order 7 period → 5 period → 3 period → 1 period, i.e. the system goes to single mode through odd cycle subtraction. On further increasing the discharge voltage, the system goes through period doubling, like 1 period → 2 period → 4 period. On further increasing the voltage, the system goes to stable state through two period subtraction, like 4 period → 2 period → stable.     

Memory effects in gas chromatographic detection with a microwave-induced plasma

Capillary gas chromatography coupled to microwave-inducedplasma detection furnishes sensitivity adequate for trace analysis when the signal is monitored at a carbon emission line. Work performed with one of these systems at high electronic gain for the carbon signal has revealed solvent band widths in excess of four minutes; these impeded quantification of peaks eluting after the solvent. This report discusses two phenomena which could be related to the unexpected intensity of this solvent response: photomultiplier tube saturation and carbon deposits in the quartz plasma discharge tube.     

红外光谱中溶剂效应机理初探——配位机制的提出

本文就红外光谱中溶剂效应机理提出了溶质和溶剂分子间的瞬时配位作用机制，认为同－溶质在不同溶剂中的振动波数不同，是由于这种瞬时配位作用改变了溶质价电子运动状态所致。据此提出了溶剂效砂的定量关系式，测定了七种溶剂配位效应常数。用这一套经验参数处理了几种取代苯甲酸的羰基伸缩振动的溶剂效应，得较好的线性关系。还发现羰基的振动波数与取代基的Ｈａｍｍｅｔｔ常数σ之间，羰基伸缩振动对溶剂效应的敏感度与σ之间，Ｈ     

On a fast direct elliptic solver by a modified Fourier method

We describe high order numerical algorithms for the solution of second order elliptic equations in rectangular domains. These algorithms are based on the Fourier method in combination with a subtraction procedure. The singularities at the corner points, arising due to non-smoothness of the boundaries, are treated explicitly using properly constructed singular corner functions. The present algorithm is a generalization of the Fast Poisson Solver developed in our previous paper. This revised version was published online in August 2006 with corrections to the Cover Date.     

Deposition conditions in tailoring the morphology of highly porous reticular films prepared by electrostatic spray deposition (ESD) technique

Spongy-like reticular structure is a unique morphology fabricated by electrostatic spray deposition (ESD) technique. The effects of solvent, substrate temperature, precursor feeding rate, static electric field strength, and deposition time on tailoring the reticular structure were investigated. Scanning electron microscopy was used to observe the film morphology. MnO_x or LiMn₂O₄ were selected as the model materials. It is found that in addition to the conventional solvent butyl carbitol, other kinds of solvents such as ethylene glycol and propylene glycol can also be used to obtain reticular films at a suitable substrate temperature. Porous films with a low cross-linking degree pore structure can be prepared by increasing precursor feeding rate or decreasing substrate temperature. Increasing the deposition time or the electric field strength helps to obtain reticular films with more homogeneous pore size distribution. In addition, the addition of a high boiling-point solvent in mixed alcohol solvent results in the increase of proper substrate temperature. It is concluded that the fluidity of the spray droplets on the surface of a hot substrate is an important factor to form a reticular film.     

Optical modulation and digital demodulation of an in-plane moiré carrier

A rotational mismatch of gratings is used to generate a fringe carrier of an in-plane moiré pattern so that specimen deformation shows itself in the form of modulation of the carrier frequency. As both the unmodulated and modulated carriers are the patterns without fringe-loop or fringe-connection, they are automatically numbered with monotonical increasing orders by a digital image processing system without any ambiguity. The orders at every pixel of the image are determined by interpolation of the orders of the tracked fringes to establish two grey image files, from the difference of which, the orders of the in-plane displacement moiré are displayed with grey-level variation.